That was four years ago.
What are the different types of irrigation valves?
Four main valve types serve residential irrigation systems. Each works differently and fits a specific use case. The most common is the globe valve , also called a manual shutoff.
It uses a screw mechanism to compress a rubber washer against a seat. You turn the handle clockwise to close. A 3/4-inch brass globe valve costs $12-$18 at standard hardware stores.
They last decades but are slow to operate. Anti-siphon valves combine a solenoid-operated valve with a built-in backflow preventer. They mount at least six inches above the highest sprinkler head in that zone.
This creates an air gap that prevents contaminated water from flowing backward. A Rain Bird ASVF-075 anti-siphon valve costs $18-$25. Flow rate tops out at 15 GPM at 50 PSI.
They are the most popular DIY valve because they satisfy code requirements without a separate backflow device. In-line valves install underground inside a valve box. They have no backflow prevention built in.
You pair them with a separate backflow preventer. 5-20 GPM with 15-150 PSI range. Cost: $16-$22.
In-line valves are quieter than anti-siphon valves and look cleaner because they are buried. Angle valves have the inlet and outlet at a 90-degree angle. You screw them directly onto a threaded riser pipe at the valve box wall.
Orbit’s 57114 angle valve costs $10-$14 and handles 8-12 GPM. These work well in tight boxes where straight in-line valves do not fit. Irrigation parts and components reference.
How does a backflow preventer work and do you need one?
A backflow preventer stops irrigation water from siphoning back into your home’s drinking supply. Most building codes require one on any permanent irrigation system. Backflow happens when pressure drops.
Imagine a fire hydrant opens down the street. That drops pressure in the municipal water line. If a sprinkler head sits in fertilizer water, that dirty water can suck backward through your pipes.
It may reach your kitchen tap. A backflow preventer physically blocks that reverse flow. Yes, you need one.
A typical residential pressure vacuum breaker (PVB) costs $40-$80. The Wilkins 720A fits 3/4-inch pipe and handles 20 GPM at 60 PSI. Dimensions are 12 inches tall with 5-inch spread between inlet and outlet.
Installation height: minimum 12 inches above the highest outlet. Installation is straightforward — mount it vertically, install shutoff valves on both sides, and test it annually. You do not need a separate backflow preventer if you use anti-siphon valves.
Those valves include atmospheric vacuum breakers in each unit. But check your local code anyway. Some jurisdictions require a main-line PVB regardless of valve type.
Your local code guide for irrigation systems will tell you exactly what your area demands.
How do you replace a broken sprinkler valve?
Replace a broken valve by cutting the pipe, removing the old unit, and gluing in a new one. Step 1: Shut off the water. Close the main shutoff valve or the system’s ball valve.
Open a manual drain or the farthest sprinkler head to relieve pressure. Do not skip this.
Step 2: Dig out the valve box. Most valve boxes are 12×18 inches or smaller. Clear enough dirt to expose the manifold and all pipe connections.
You need room for a PVC cutter or hacksaw. Budget 20-30 minutes for this step alone. Step 3: Cut the valve out.
Use a PVC ratchet cutter for clean square cuts. Cut at least two inches from each side of the valve body. You need room to glue couplings onto the remaining pipe ends.
A standard manifold uses 1-inch PVC schedule 40. 00 each. Step 4: Install the new valve.
Dry-fit everything first. Measure twice. Glue once.
Apply PVC primer to the pipe end and coupling inside, then PVC cement. Push and twist a quarter-turn. Hold for 15 seconds.
Let it cure for 30 minutes before testing. A complete manifold rebuild (valve + fittings) costs $25-$45 in parts. If you have multiple failed valves on the same manifold, consider replacing the whole assembly. Irrigation repair guide has photos of each step.
What is a solenoid valve and how do you test it?
A solenoid valve uses an electromagnetic coil to lift a plunger and open the water path. Test it by checking for clicks, continuity, and resistance values. The solenoid is the electrical heart of the valve.
It sits on top of the valve body with two small wires connected to the controller. When the controller sends 24V AC power, the coil creates a magnetic field. That lifts a small metal plunger.
Water then flows through the center of the diaphragm and opens the valve. When power stops, the plunger drops and the valve closes. A replacement solenoid costs $8-$15.
Hunter’s PGV solenoid uses two standard 18-gauge wires and operates at 24V AC with a holding current of 350 mA. Testing a solenoid takes two minutes. You need a multimeter capable of reading ohms.
Disconnect the two solenoid wires from the controller. Set your multimeter to 200 ohms. Touch the probes to each wire.
A working solenoid should read between 20 and 60 ohms. Hunter solenoids typically read 25-35 ohms. Rain Bird reads 35-50 ohms.
If you get zero, the coil is shorted. If you get infinite (OL), the coil is open and dead. Replace it.
If the reading is correct but the valve still does not open, the plunger may be stuck from debris. Unscrew the solenoid, rinse the plunger, and reinstall. That fix costs zero dollars and works more often than you think.
How do you install a backflow preventer?
Install a backflow preventer by connecting it between your main shutoff and the first zone valve. Mount it vertically and above ground for easy access and code compliance. Choose your location carefully.
The backflow preventer must be at least 12 inches above the highest sprinkler head or outlet in your system. In practice, that means mounting it on an exterior wall near the water source. Direct sunlight degrades the plastic test cocks and relief valve over time.
Consider a shaded north or east-facing wall. A Wilkins 720A PVB costs $48-$62. 5 inches tall, 3-inch inlet/outlet spacing, and 3/4-inch threaded female connections.
Step 1: Install shutoff valves on both sides. You need a ball valve on the inlet and one on the outlet. This lets you isolate the backflow preventer for testing or replacement without draining the whole system.
Ball valves cost $8-$12 each. Step 2: Mount the backflow preventer. Use two pipe straps or a mounting bracket.
Keep it vertical — horizontal installation causes test failures. Leave six inches of clearance below the relief valve. That valve can spit water during normal operation.
Aim it away from your foundation and electrical service. Step 3: Connect and test. Use PTFE tape on all threaded connections.
Open the inlet valve slowly. Check for leaks at every joint. Open the test cocks and confirm water flows freely.
Close the outlet valve and check that the backflow preventer holds pressure. If the relief valve drips continuously, you have debris on the seat or incorrect inlet pressure (should be under 80 PSI). An installation takes 1-2 hours for a homeowner. For winterization, you must drain the PVB before freezing weather. How to winterize your irrigation system complete blow out guide covers blowout procedures in detail.
Which valve brand should you choose: Rain Bird, Hunter, or Orbit?
Each has trade-offs in price, durability, and parts availability. Rain Bird makes the most widely available residential valve in the United States.
Their 100-DVAS anti-siphon valve costs $16-$22. 5-15 GPM with 15-150 PSI. You can find replacement diaphragms and solenoids at any hardware store.
The downside: the DV series uses plastic threads on the bonnet that strip easily if you overtighten by hand. Rain Bird also makes the 100-HV in-line valve ($18-$25) with better thread quality. Parts availability is the best of any brand.
Their PGV series in-line valve costs $18-$24. 5-20 GPM with 15-150 PSI. The bonnet uses a captured O-ring that stays in place during reassembly.
That is a small detail that saves you hours of frustration. The PGV-101-GV (3/4-inch) costs $19-$22.
The PGV-201-GV (1-inch) costs $22-$26. Solenoids are $10-$14. Hunter parts are slightly harder to find locally.
Orbit is the budget pick.
Their 57114 anti-siphon valve costs $10-$14. The 57624 in-line valve costs $12-$16. That is 40% less than Rain Bird or Hunter.
The trade-off is durability. The plastic feels thinner.
The threading wears faster. The flow rate is 5-12 GPM with 10-100 PSI — lower than the competition. Consider Orbit only for temporary systems or rental properties where you do not care about longevity.
If you plan to own your home for more than two years, spend the extra $6-$10 for Rain Bird or Hunter. If you need anti-siphon (no separate backflow preventer), get Rain Bird 100-DVAS.
Skip Orbit unless your budget is under $50 for the whole manifold. Practical guidance: Valves and backflow preventers are the most critical components of any irrigation system.
Mount your backflow preventer where you can see it and test it every spring. The morning you find a stuck solenoid and a flooded yard is the morning you will wish you had spent the $12 on a spare. You will too.
com/products/plumbing-flow-control-solutions/backflow-prevention)
Disclosure
Last updated: 2026-06-09T03:57:49. This article contains affiliate links and practical recommendations based on hands-on testing. I may earn a commission when you purchase through these links, at no extra cost to you. All opinions are my own and based on real-world irrigation experience.
Tested & Verified: All product recommendations have been tested in real irrigation systems. Last review date: 2026-06-09T03:57:49.